Protective clothing free shipping, delivered within 5-7 days >>>

Company Tel: +86 755 27087205   Mobile: +86 13662677207 (Same number for WeChat)     Email:  yy@youyigarment.com

Shenzhen Youyi Protection Technology Co., Ltd.
CN
Dustproof ESD Workwear Dustproof ESD Workwear

Dustproof ESD Workwear

News / 2026.11.12

  Dustproof ESD Workwear: Reconciling Particle Control with Static Dissipation

  In lithium battery electrode shops, precision electronics assembly lines, powder dosing areas and some pharmaceutical clean zones, workers are at once carriers of dust and generators of static. A garment designed only for dust exclusion leaves static with nowhere to go; a garment designed only for static control has a fabric structure that lets particles through. The two requirements are not naturally consistent in one fabric and must be reconciled through structure, material and the supporting system together.

  1. How the two risks overlap

  Dust risk works in two directions: external dust entering the product and process environment, and particles from the worker's own skin flakes and fiber debris spreading outwards. Static risk comes from charge accumulated by body movement, whose discharge can attract dust, damage devices, or act as an ignition source in combustible dust atmospheres. The two reinforce each other: a charged surface attracts particles, while deposited dust alters the conductive state of the fabric surface and creates local insulation.

  2. Reconciling them at fabric level

  Dust exclusion depends mainly on fabric density. Continuous filament polyester sheds less than staple fiber, and a tight twill or plain weave is denser than an open structure; some areas use a laminated microporous membrane to block particles at the cost of moisture permeability. Static control relies on embedded conductive yarn forming a network, usually at 5 to 10 millimetres spacing and interwoven with the base fabric to create a continuous path. Note that in laminated structures the membrane itself is insulating, so the conductive network must be placed on the outer side of the membrane or connected to the wearer through a dedicated path; otherwise charge is trapped behind the membrane and the dissipation path is cut. Filtration efficiency and breathability should both be assessed, and the balance depends on dust concentration at the workstation and work intensity.

  3. Closure-oriented construction

  Particle control depends heavily on the number of openings. A coverall removes the waist break, and a hood integrated with the body prevents hair and skin flakes from escaping. Cuffs, ankle openings and collars use rib or elastic closures to limit air exchange. The front closure uses a zip with a studded placket and a backing flap behind the zip so that the seam is not a particle path. Pockets are a high-risk feature, since dust accumulates inside and is released on movement; high-cleanliness areas generally adopt pocketless designs. Seams are overlocked or taped to reduce needle holes and loose ends.

  4. Details of contamination control

  Accessory materials affect shedding and static. Ordinary plastic zips generate debris through friction, so low-outgassing materials are preferable; metal parts may bring corrosion and particles in clean zones, yet in explosion-protection areas frictional sparking must be avoided, so the choice follows site conditions. Conductive sewing thread supports both seam continuity and fewer loose ends. Gowning sequence matters as well: ordinary synthetic clothing should not be worn underneath, and changing should take place in the airlock rather than shaking garments inside the clean zone.

  5. Completeness of the dissipation chain

  The garment is only one link. The chain runs through the wearer, the garment, footwear, flooring and earthing. The resistance of anti-static shoes must match the system resistance of the floor; if the floor is insulating or unearthed, even an intact conductive network has nowhere to discharge. Where wrist straps are impractical, shoes and flooring become the main path. Humidity has a marked effect: below about 40 percent relative humidity the surface resistance of most materials rises and dissipation slows, so humidification or process control is needed to hold conditions steady.

  6. Washing and degradation

  Repeated washing abrades the coating on conductive yarn and also loosens the fabric structure, increasing shedding. Laundering should avoid softeners and silicone additives, which form an insulating film on the fibers, and strong oxidizing bleaches, which accelerate ageing of the conductive layer. Water temperature, mechanical action and drying should follow the fabric instructions, and finishing and packing should take place in a clean environment after washing so that particles are not re-adsorbed in ordinary air. Under GB 12014-2019, the garment must still meet the resistance requirement after the specified number of washes.

  7. Testing and selection

  Static performance is tested to GB 12014-2019 for point-to-point resistance within the range 1×10⁵ to 1×10¹¹ ohms, together with charge quantity; fabric electrostatic propensity can be compared by the manual rubbing method of GB/T 12703.2-2021 or the corona charging method of GB/T 12703.1-2021. On the particle side, shedding and filtration efficiency are the focus, with different requirements for different cleanliness classes. Both reports should be reviewed together at selection rather than purchasing and accepting them separately.

  8. Common misconceptions

  One is using ordinary anti-static garments as cleanroom garments, whose shedding may exceed what the clean zone allows. Another is looking only at fabric data and ignoring leakage at openings and seams. A third is assuming a coverall can replace the gowning procedure, when a chaotic sequence brings in large amounts of particles. A fourth is adding softener in the wash, which makes conductivity decay quickly. A fifth is supplying garments without shoes and earthing, which leaves static control nominal.

  9. Conclusion

  Whether dust exclusion and static control can coexist depends on consistency between fabric structure, closure design and the dissipation chain. Verify all three together, and the workwear both blocks particles and releases charge.

RELATED RECOMMENDATIONS

EN ISO 11612 Protective Clothing

EN ISO 11611 Flame Retardant Suit

EN ISO 11612 Flame Retardant Suit

Fire Fighting Suit with EN469 Certification

Fire Fighting Suit for Petrochemical Industry