Company Tel: +86 755 27087205 Mobile: +86 13662677207 (Same number for WeChat) Email: yy@youyigarment.com
ESD Separate Jacket & Trousers: Managing the Break at the Waist and the Supporting System
In electronics assembly, precision instruments, pharmaceutical and chemical workstations of low to medium risk, two-piece garments are widely used because they are easy to put on and off and adapt well to different body sizes. Compared with a coverall, they leave a natural break at the waist: inner clothing may show between jacket and trousers, and the conductive network may be interrupted there. Whether a two-piece works well depends on how carefully that break is handled.
1. What two-piece garments offer, and what they cost
The advantages are freedom of movement and low replacement cost, since a worn jacket or trouser can be replaced separately. The cost is that the waist becomes the weakest point in the protection chain. If the jacket hem rides up when the wearer bends, inner clothing is exposed; if the trouser waistband has no conductive path, the charge networks of the two garments behave like two disconnected wires. This premise should be acknowledged at selection, and the break closed through design and management.
2. Three ways to handle the waist interface
One is tucking the jacket hem into the waistband, relying on overlap to maintain charge and particle continuity, though it can pull out when bending. Another is an extended hem covering below the hip with an elasticated bottom, suited to workstations with large movement ranges. The third is a conductive overlap at the waist, for example a conductive tape on the inside of the jacket and another on the outside of the waistband, joined by studs or fasteners so that the networks conduct while worn. This third approach costs more but is more reliable in static-sensitive areas; at acceptance, continuity between jacket and trousers should be measured with the garment actually worn.
3. Consistency of fabric and network
Jacket and trousers should come from the same batch and structure. Batches may differ in conductive yarn spacing, weave and finishing, and mixing them produces uneven charge distribution. Pattern layout should respect the direction of conductive yarn, avoiding large misalignment between the grids of trouser and jacket panels. Cutting severs conductive yarn, so the binding at the jacket hem and waistband should be complete and not omitted for lightness. Where the two pieces come from different suppliers, test point-to-point resistance separately at acceptance, then test the combination as worn.
4. Seams and components
Conductive sewing thread should be used; ordinary polyester thread forms an insulating barrier at seams. Load-bearing points such as armholes, trouser crotch and pocket openings need reinforcement, and the method should not damage the conductive network. Zips and snaps have different material requirements in clean and explosion-protection settings: plastic parts that shed debris are avoided in clean zones, while metals that spark under friction are avoided in explosion-protection zones. Pockets should be minimised, since pocket openings and pocket bags accumulate both charge and dust.
5. The supporting system determines actual performance
Two-piece garments are usually combined with anti-static shoes and static-dissipative or earthed flooring. If the shoes are insulating and the floor is unearthed, the garment's conductive network has nowhere to discharge. For roles requiring frequent walking, shoes and flooring are the main path; fixed workstations may add wrist straps, provided contact with skin is reliable. Below about 40 percent relative humidity, surface resistance of most materials rises and dissipation slows, so humidification or process control is needed.
6. Washing and batch management
Jacket and trousers should be washed together in the same batch. If one has been washed many times while the other is still new, the resistance difference between them becomes too large. Softeners and silicone additives must not be used, as they form an insulating film on the fibers; strong oxidizing bleaches accelerate ageing of conductive yarn. Water temperature, mechanical action and drying follow the fabric instructions. Under GB 12014-2019, the garment must still meet the resistance requirement after the specified number of washes, so post-wash test data should be requested at purchase.
7. Testing and acceptance
Point-to-point resistance is tested to GB 12014-2019, with the range from 1×10⁵ to 1×10¹¹ ohms, together with charge quantity. For two-piece garments, jacket and trousers should be tested separately, then checked for continuity while worn. Fabric electrostatic propensity can be evaluated by the manual rubbing method of GB/T 12703.2-2021 or the corona charging method of GB/T 12703.1-2021. Where resistance exceeds limits, check washing practice and seam construction first before replacing, rather than scrapping the whole batch.
8. Common misconceptions
One is assuming two-piece and coverall garments give equivalent protection and ignoring the waist break. Another is mixing jacket and trousers from different batches or even different makers without testing the combination. A third is treating a tucked hem as a complete solution without assessing whether it pulls out during movement. A fourth is adding softener in the wash. A fifth is supplying garments without shoes and earthing, leaving static control nominal.
9. Conclusion
The value of a two-piece is flexibility, and its risk is the break. Handle the waist interface, fabric consistency and supporting system properly, and two-piece garments serve most workstations reliably.